Construction products detail

Other load-bearing plastic elements

Load-bearing plastic elements are used to manufacture, inter alia, pultruded plastic profiles, service ducts, balcony floor slabs, heavy-duty brackets and brackets for transferring loads from attachment parts. Fibre-reinforced plastics, polymer concretes, wood-polymer composites (WPCs) and other composite materials are most commonly used for them.

Regulatory framework

DIBt grants national technical approvals (abZ) for load-bearing plastic elements. European Technical Assessments (ETAs) can also be issued for these products.

There are no conclusive technical rules for the design and execution of construction techniques comprising the above-mentioned load-bearing plastic elements. DIBt therefore grants general construction technique permits (aBG) for these applications. National technical approvals and general construction technique permits are usually granted together in a single decision ('combined decision').

Please also note the relevant provisions of the federal states following MVV TB, A 1.2.2 to A 1.2.9.

Note: There are no conclusive technical rules for the design and execution of construction techniques comprising the above-mentioned load-bearing plastic elements. If required, please apply for a general construction technique permit (aBG). Cf. MVV TB, A 1.2.2 to A 1.2.9.

EAD 220010-01-0402 Flat plastic roofing sheets made of recycled plastic for self-supporting and/or fully supported discontinuous roofing and/or external cladding (26 pages ) Version: May 2019; Decision (EU) 2020/962; superseding "EAD 220010-00-0402"; EOTA EAD 260001-00-0303 Structural sections made from fibre reinforced polymers (FRP/Glassfiber Composites) (16 pages ) Version: January 2016; OJEU 2017/C 379/07; EOTA EAD 340287-00-0203 Reinforced high density EPS structural panel system for building units (31 pages ) Version: July 2020; Decision (EU) 2022/381; EOTA

National procedure

A national technical approval (abZ) and/or oder general construction technique permit (aBG) is granted upon application (see Model Building Code (MBO), Sections 16a(2) and18(2) and (4)). This also applies to amendments and supplements to, or renewals of existing approvals and/or construction technique permits.

No formal requirements apply. The following information is needed: name and address of the applicant, description of the product and/or construction technique and its field of use or application, type of decision required (new decision, amendment or supplement to, or renewal of, an existing decision).

Please feel free to use the template below.

European Technical Assessment (ETA)

To start the ETA procedure, please submit the form below. We will then check if the prerequisites for issuing an ETA are met, i.e., in particular, if the product is not fully covered by an existing harmonised standard. If the prerequisites are met, we will check whether a European Assessment Document (EAD) covering the requested assessment scope already exists or still needs to be developed. If an EAD needs to be developed or amended, a complete technical file needs to be established before the procedure can begin.

aBG

Z
new decision
E
supplement
Ä
amendment
V
renewal
G
valid until
Subject concerned Applicant Decision no. Validity
from / to
Tragende Konstruktionsprofile aus glasfaserverstärkten Kunststoffen nach ETA-16/0901; Doppel-T-Profile, U-Profile, Winkelprofile, Vierkanthohlprofile, Flachprofile und Handlaufprofile Fiberline Building Profiles A/S Strevelinsvej 38-40 7000 FREDERICIA DÄNEMARK Z-10.39-791 Z: 21.07.2023
G: 09.05.2028
Mastoberteil "HEM 3 kN" aus glasfaserverstärktem Kunststoff für die Befestigung von Traversen für Freileitungen FUCHS Europoles GFK GmbH Europoles-Straße 1 92318 Neumarkt Z-10.9-591 Z: 10.06.2022
G: 10.06.2027
Pultrudierte Profile "krafton" aus glasfaserverstärktem Kunststoff zur Verwendung als tragende Bauteile krafton Beheer BV Markweg Zuid 34 (ind. terr. Dintelmond), Havennummer 5203 4794 SN HEIJNINGEN NIEDERLANDE Z-10.9-803 Z: 12.12.2023
G: 05.12.2028